Fiber Optic
The Story Of Legacy Fiber Optic Connectors
:: Choices of connectors
Over the years, a large variety of fiber optic connectors have been designed for most fiber optic installations. Lightwave equipment manufacturers have never standardized on any one connector type, they actually provide a selection of connectors for their equipment interface.
It is very important to choose the fiber connector type for your applications. You should maintain a connector standard throughout a fiber optic project.
:: The components of a fiber connector
For most fiber optic connectors, the major components are ferrule, connector body, connector cap and strain-relief boot.
Ferrule
The ferrule is the center part of the connector. It contains the optical fiber in a center hole. Ferrule can be made from ceramic (Zirconia), stainless steel or composite material.
Ceramic ferrule is the most popular material since it has stable temperature characteristics. The most common ceramic is Zirconia which is a white hard ceramic material. Ceramic ferrule is used for both single mode and multimode connectors. It offers the lowest insertion loss and the best repeatability.
Connector Body
Fiber optic connector body can be steel or plastic. The body design differs from connector to connector. The connector body provides the mechanism to hold the ferrule and other parts together. It also provides the locking mechanism for connector mating. The most common locking mechanisms are push-pull, snap-in, thread on and twist-on.
Connector Cap
Connector cap often has the same material as the body: either steel or plastic. The cap can be screw on, twist lock or snap-on for connector mating.
Strain-relief Boot
Strain-relief boot is the part connecting the connector body and the fiber cable. It is often made from rubber. Although it looks minimal, it is actually one of the most critical parts in a connector. It provides strain relief on the optical fiber to prevent micro-bending, breakage and provides mechanical support for fiber and connector handling.
:: Legacy Fiber Connector Types
The following list shows the legacy connector types that have been deployed in numerous fiber optic networks for many years.
ST Connector
ST connector was once the most popular fiber connector. It was well-liked for both single mode and multimode fiber connections. The average insertion loss for a ST connector is about 0.5dB.
ST connector has a twist-on locking mechanism which is not susceptible to loosening in vibrating environment. It is most often used in LAN networks.
FC Connector
FC connector is popular for single mode applications. It has the lowest insertion loss and the best repeatability. It has a thread-on locking mechanism.
SMA connector
SMA connector is a pretty old connector type which is mostly used for multimode applications. Today it is still being using on medical equipment.
There are two types of SMA connectors on the market: SMA 905 and SMA 906. The only difference between them is that SMA 906 has a straight ferrule while SMA 905 has a step-down ferrule.
D4 Connector
The NEC D4 was probably the first connector to use ceramic or hybrid ceramic/stainless steel ferrules. It uses a smaller ferrule than SCs or FCs. It was widely used in telco networks in the 80s to early 90s and some may still be in use.
FDDI connector
Besides the SC Duplex, you may occasionally see the FDDI duplex connectors which mate to their specific networks. They are generally used to connect to the equipment from a wall outlet, but the rest of the network will have ST or SC connectors. Since they both use 2.5 mm ferrules, they can be mated to SC or ST connectors with adapters.
Biconic Connector
Biconic connector's yellow body indicating a SM version - mutlimode versions were usually black. Biconic connector was developed by a team led by Jack Cook at Bell Labs in Murray Hill, NJ.
About the Author
Colin Yao is an expert on fiber optic networking technologies and products. Learn more about
bulk single mode fiber
,
corning fiber optic cable
,
outdoor single mode fiber
on Fiber Optics For Sale Co. web site.
Fiber Optic
 |
 Fiber Optic Lighting DOUBLE Combo Pack 150 feet of each 1 LED illuminator  US $99.99
|
 150 Ft of 25 50 75 10mm Fiber Optic Filament DOUBLE Combo Pack 4 SIZES US $79.99
|
 Fiber Optic Lighting Combo Pack with LED illuminator US $54.99
|
 75 feet of 25 50 75 10mm Fiber Optic Filament Combo Pack FOUR SIZES US $39.99
|
 400 feet Colored FIBER OPTIC fiber Model Lighting Model RR etc FREE Bonus US $21.99
|
 Light your Layout 75 ft of 10mm Fiber Optic Filament US $17.75
|
 Fiber Optic for Layout Lighting Effects 75 feet 75mm US $11.75
|
 75 feet of 75mm Fiber Optic Filament for Model and Craft Lighting End Glow US $11.75
|
 100 feet 75mm FIBER OPTIC MODEL RR LIGHTS FREE bonus US $11.99
|
 100 feet 75mm FIBER OPTIC fiber for MODEL RR LIGHTING and more FREE Bonus US $11.99
|
 200feet 50mm FIBER OPTIC fiber for MODEL RR layout LIGHTING etc FREE Bonus US $11.99
|
 O On3 F Fn3 Fiber Optic Combination pack for Structure Scenic Lighting US $9.95
|
 HO HOn3 Fiber Optic Combination pack for Structure Scenic Lighting US $9.95
|
 Optic Fiber 060 for Building Lighting Model Scenery US $5.95
|
 HO Hon3 Optic fiber sample pk for Bldg Lighting Scenery US $5.40
|
 O On3 Fiber Optic sample pack for Structure Scenic Lighting US $5.40
|
 Optic fiber sample pk model Building Lighting Scenery US $5.40
|
 Optic Fiber 030 for Building Lighting Model Scenery US $4.25
|
How do i plug a fiber optic plug into my xbox?
I have a surround sound system and im just trying to figure out where the fiber optic cable plugs into on the xbox
If by Xbox you mean the 360, then there's a connection on the AV cable that you can use an optical connector with. At least, it's there for the HD and VGA cables. If you're using HDMI, then there's a bit you can plug into the AV port that gives you the connection, but you only get that bit if you buy Microsoft's HDMI cable or if you have an older Elite.