Depot Kit
How to Remove an Aftermarket Wood Dash Kit From Your Car
You're right to expect that this will be quite a bit of work, but it's something you can definitely do at home if you have some time and patience. Bottom line, it can get messy and it is time consuming, so there are a few ground rules that we need to set first before you begin this project.
Here's what you'll need -
1. Plenty of time
2. Heat gun or hair dryer
3. Goof Off (or similar glue remover)
4. Lots of clean rags
5. Replacement dash trim kit (maybe)
First, the big question. Are you absolutely sure its an aftermarket wood dash kit? These instructions only apply to an aftermarket installed wood dash kit. These type kits are overlays, (usually installed at the local car dealerships) and can be removed with some persuasion. However if you have a factory installed dash kit, and by factory I mean installed at the manufacturing plant level (not the dealership) you can not remove the kit without replacing the entire dash part. The wood will not separate from the dash in this instance. If you are sure its an add-on aftermarket dash kit then we are good to go.
Second, be sure to pick a day when you have a good block of time open because this is not something you can rush. So that means that you need to pick a day that you are off from work, and no doctor or dentist appointments. Also, you need to be prepared to (more than likely) reinstall a replacement dash kit to cover up any markings left by the old kit that you are removing. Sometimes you can get lucky and it wont leave any marks, but most of the time there will be some type of markings such as outlines or discoloration of the dash.
To begin, you'll want to use a hair dryer and try to heat up the wood dash kit as much as possible. That will soften the glue to some extent, and you can try to start pulling up a corner of the dash piece slowly and lifting it off. and it is important that you really warm it up good or it will be very hard and brittle, making it tougher and more time consuming to remove. I wouldnt use any sharp tools here, though you will be tempted to do so. Try just using your fingers to pull, as anything sharp used will likely damage your dash.
Take your time! Once you get a piece off you will more than likely be left with some glue or adhesive. Warm that up again and try to remove that best as you can without any solvents (just the first step). Then, when you do need some solvent, try a glue remover like goof-off (available at home improvement stores such as Home Depot) but be very careful where you wipe it. If you get that on any of your new surfaces you may get some discoloration. Just be careful and use it sparingly. A damp rag is much better in this case than a dripping wet one. If you need to use a soft rubber squeegee to agitate the adhesive with the solvent, that is okay - but steer clear of razors or metal objects. You will damage your interior with those.
If you are uncomfortable performing this task or find that you do not have enough experience, we always recommend professionals to to this project. Call your local body shop and discuss further options with them so you dont damage your vehicle.
About the Author
Mike Briglia is the owner of Custom Auto Trim, a car accessories company based out of San Diego CA. Find more information on dash kits at http://www.customautotrim.com/
Depot Kit
 |
 HO Scale MILWAUKEE STATION BRICK DEPOT TRAIN SHED KIT  US $399.94
|
 RIVERA DEPOT HO Santa Fe Model Railroad Structure Wood Laser Kit BT673 US $139.95
|
 BANTA MODELWORKS OPHIR DEPOT HO HOn3 Model Railroad Structure Wood Kit BM117 HO US $137.95
|
 BANTA MODELWORKS DRGW RAILROAD SILVERTON DEPOT HO Structure Kit Kit BM2089 US $133.95
|
 RANDOLPH DEPOT HO HOn3 Model Railroad Structure Unpainted Wood Laser Kit RSL203 US $129.95
|
 Laser Kit Nenana Alaska Railroad Depot HO Scale US $129.95
|
 DRG DELORES DEPOT LASERKIT by AMERICAN MODEL BUILDERS KIT 803 US $119.98
|
 DIVISION POINT DEPOT HO SCALE KIT 131 by MODEL MASTERPIECES US $119.95
|
 Durango Silverton DSRR Silverton Depot Kit BANTA MODEL WORKS NEW HO HON3 US $112.89
|
 American Model Builders HO 805 Santa Fe 5 Depot kit US $110.00
|
 American Model Builders HO 803 Dolores Depot kit US $110.00
|
 GCLASER HO GC LASER CUT JUNCTION CITY DEPOT KIT13371 US $109.95
|
 SRRL RUBBLES DEPOT LOADING DOCK KIT YORKE SCALE MODEL MASTERPIECES HOn30 HOn3 US $104.95
|
 BANTA MODELWORKS DENVER RIO GRANDE RAILROAD MONERO DEPOT HO Wood Kit BM2137 US $102.95
|
 BANTA MODELWORKS SRRL RAILROAD PHILLIPS DEPOT HO Railroad Structure Kit BM2099 US $98.95
|
 CENTER HALL DEPOT HO Model Railroad Structure Wood Laser Kit BT663 US $97.95
|
 STANDARD DEPOT HO CRAFTSMAN KIT 10 BY MASTER CREATIONS OLD VERY RARE US $95.00
|
 JUNCTION CITY DEPOT LASER CUT KIT BY GCLASER SUPER SPECIAL SALE PRICE HO SCALE US $89.99
|
 BANTA MODELWORKS DENVER RIO GRANDE DEPOT HO Railroad Structure Kit BM2104 US $87.95
|
 American Model Builders HO 142 Santa Fe Depot Kit US $84.95
|
 BRANCHLINE TRAINS LAZER ART HO STRUCTURE BUILDING KIT Center Hall Depot Kit 663 US $82.99
|
 RIVERA DEPOT LASER CUT WOOD KIT BY LASER ART SPECIAL SUPER PRICE FOR THIS KIT US $79.78
|
 American Model Builders HO 127 UP Standard Depot Kit US $76.99
|
 American Model Builders HO 182 Union Pacific Depot kit US $76.59
|
 AMB HO ATSF Combination Depot Wood Building Kit US $74.98
|
 Gerald Depot Laser Cut Kit Building Blair Line HO Scale 187 Model RR Trains US $74.49
|
I got a 68 inch Hampton Bay Altura Ceiling fan, I need a light kit for it and can't find it, where do I go?
I bought a 68 inch Hampton Bay Altura ceiling fan from Home Depot. It doesn't come with a light kit.
They do not have the proper light kits at Home Depot because the fan is too big, or the part where the fan goes into is too large.
They told me to go to Hampton Bay's website, and I can't find any specific light kit for that ceiling fan. I've called customer service but they keep telling me to look on the website.
Please help! My room is dark!
If I remember correctly, the cover where you install the light kit has 3 phillips head screws. Take them out (don't lose them) and take the cover to as many home improvement centers and electrical supply houses as you can find. You may be able to locate a light kit that is the same size without regards to the brand name. Also an electrical supply house may be able to direct you to an electrical appliance store that carries that brand. It is a well known brand and you may need help from the web site but those "*"*"* have a habit of changing and complicating their part numbers for the same items. Use the part number and model number in the "Contact Us" box and request an Email reply. (of course you can expect "We don't stock that item any more") for an answer.
Good Luck ! ! ! (I live in Spain now and every brand is a different size)